Instructions for Reprocessing of Reusable Surgical Instruments

The following instructions are for all reusable medical devices supplied by BusinessMed Instruments, unless stated otherwise with the packaging of the product. These instructions are intended for use only by persons with the required specialist knowledge and training.


  • Follow instructions and warnings as issued by the manufacturers of any decontaminate, disinfectants and cleaning agents. Wherever possible avoid use of mineral acids and harsh, abrasive agents.
  • No part of the process shall exceed 140 °C.
  • Some sensitive materials (e.g. Aluminum) are damaged by high alkaline solutions (pH>10).
  • Devices with long, narrow cannula, hinges and blind holes require particular attention during cleaning.

Note: When reprocessing medical devices, always handle with care, wearing protective clothing, gloves and eye-wear in accordance with local health & safety procedures.

Limitations on Reprocessing

  • Repeated processing has minimal effect on these instruments.
  • End of life normally determined by wear and damage in use.
  • Any specific limitations on the number of reprocessing cycles shall be made available with instrument.

From Point of Use

Whenever possible, do not allow blood, debris or bodily fluids to dry on instruments. For best results and to prolong the life of the medical device reprocess immediately after use. If they cannot be reprocessed immediately, use an enzymatic foam spray cleaner to help prevent soil from drying.

Preparation for Decontamination
Process all the instruments as soon as it is reasonably practical following use.
Disassemble only where intended, without the use of tools unless specifically provided by the manufacturer. Instructions for disassembly are available with the device, where required.

Cleaning: Automated

  • Use only either CE marked or validated washer-disinfector machines and low foaming, non-ionizing cleaning agents and detergents following the manufacturer’s instructions for use, warnings, concentration and recommended cycles.
  • Load instruments carefully, with any box joints and hinges open and so that any fenestration in instruments can drain.
  • Place heavy instruments with care in the bottom of containers, taking care not to overload wash baskets.
    Place instruments with concave surfaces facing down to prevent pooling of water.
  • Where possible, use appropriate attachments to flush inside reamers and devices with lumens or cannula.
  • Ensure that soft, high purity water which is controlled for bacterial endo-toxins is used in the final rinse stage.

Note: Automated cleaning may not be suitable for all lumens and cannula in which case clean manually with a water jet gun, if available, and an appropriate brush (and stilette if provided) that reaches the depth of the feature. After manually cleaning, pass all devices through an automatic cleaning cycle to achieve disinfection.

Note: These instruments have been validated using a washer-disinfector cycle validated to include two cold rinses at <35 ºC, a detergent cycle and a rinse cycle both at >50ºC, a disinfection cycle operating at a temperature of between 80 ºC and 90 ºC for a minimum holding time of 1 minute (actual holding time in excess of 2 minutes 50 seconds) and a 20 minute drying cycle. The detergent used was low foaming, non-ionizing spray wash detergent cleaner (max 12pH) and the rinse aid a neutral pH low foaming, non-ionic surfactant with isopropyl alcohol.

Cleaning: Manual
Manual cleaning is not advised if an automatic washer-disinfector is available. If the equipment is not available, use the following process:-
Use a double sink system (wash/rinse) dedicated for instrument cleaning (not used for hand washing). Ensure that the water temperature does not exceed 35 of the re-processor to ensure that the reprocessing as actually performed using equipment, materials and personnel in the reprocessing facility achieve the desired result. This requires validation and routine monitoring of the process. Likewise any deviation by the re-processor from the instructions provided must be properly evaluated for effectiveness and potential adverse consequences..
In the first sink, keeping the instrument submerged, with an autoclavable brush, apply CE marked cleaning solution to all surfaces until all soil has been removed. Pay particular attention to serrations, teeth, ratchets and hinges, always brushing away from the body and avoiding splashing. Ensure rongeurs and hinged instruments are thoroughly cleaned in both open and closed positions.
In the second sink, rinse instruments thoroughly with soft, high purity water which is controlled for bacterial endotoxins, so that the water reaches all parts of the instrument, then carefully hand dry or use a drying cabinet.

Note: Manual Cleaning is NOT a disinfection process: When manual cleaning is used it may not be possible to disinfect the device prior to further handling.

Cleaning Inspection
After cleaning visually inspect, visually inspect all surfaces, cannulations, ratchets, joints, holes and lumens for complete removal of soil and fluids. If ANY soil or fluid is still visible, return the instrument for repeat decontamination.

Apply surgical grade lubricant to hinges, joints and moving parts as per the lubricant manufacturer’s instructions.

Inspection and Functional Testing

Visually inspect and check: – all instruments for damage and wear; cutting edges are free from nicks and present a continuous edge; jaws and teeth align correctly; all articulated instruments have a smooth movement without excess play; locking mechanisms (such as ratchets) fasten securely and close easily; long, slender instruments are not distorted; any component parts fit and assemble correctly with mating components.
Remove for repair and replacement any blunt, worn out, flaking, fractured or damaged instruments.

Note: If an instrument is returned to the manufacturer / supplier, the instrument must be decontaminated and sterilized and be accompanied with the relevant documented evidence.

All instruments to be packed following local protocol in accordance with ISO 11607-1 or AAMI/CSR technique.

Sterilization (USA)
Autoclave should comply with the requirements of, and be validated and maintained in accordance with ANSI/AAMI ST79.
Pre-Vacuum moist heat sterilization operating at temperature 132 °C bar for a minimum holding time of 4 minutes – always following the instructions of the machine manufacturer.
When sterilizing multiple instruments in one autoclave cycle, ensure that the sterilizer manufacturers stated maximum load is not exceeded.
Ensure instruments are dry before sterilization.

Sterilization (In other Countries)
Autoclave should comply with the requirements of, and be validated and maintained in accordance with EN 285, EN 13060, EN ISO 17665.
Either CE marked or validated vacuum autoclave operating at 134-137 °C bar for a minimum holding time of 3 minutes – always following the instructions of the machine manufacturer.
When sterilizing multiple instruments in one autoclave cycle, ensure that the sterilizer manufacturers stated maximum load is not exceeded.

Ensure instruments are dry before storage, and stored in dry, clean conditions at an ambient room temperature.